dismiss

Visit DOTmed at RSNA 2014, Booth 6608, North Hall - Nov. 30 - Dec. 4

SEARCH
Current Location:
>
>
> Xenon Nova 20131520, Karl Storz Service Manual

Xenon Nova 20131520, Karl Storz Service Manual

(46)
(1)
(2)

Laiq Ahmed

Xenon Nova 20131520, Karl Storz Service Manual

June 23, 2009 01:10

Dear All.
I am looking for Xenon Nova 20131520, Karl Storz Light source service manual or schematics diagrams.
Thanks in advance.
Regards
LAIQ

Log inor Register

to rate and post a comment

(13)

Milan Janca

Re: Xenon Nova 20131520, Karl Storz Service Manual

June 23, 2009 08:02

Try this link
https://www.karlstorz.com/cps/rde/xchg/SID-66403E2B-AF49A7B9/karlstorz-en/hs.xsl/2254.htm

Log inor Register

to rate and post a comment

(46)
(1)
(2)

Laiq Ahmed

Re: Xenon Nova 20131520, Karl Storz Service Manual

June 24, 2009 07:22

Dear Milan
Thanks for your reply. But cant see the download link or any pdf link. Any explaination will be great. Thanks again.

Log inor Register

to rate and post a comment

(22)

(1)

Geoff Hannis

Re: Xenon Nova 20131520, Karl Storz Service Manual

June 25, 2009 09:31

You probably need to Register, there, Mate.

Try that and see if Storz will send you the manual. You'll never know until you try!

Cheers.

Log inor Register

to rate and post a comment

(5)

Enrique Moreno

Re: Xenon Nova 20131520, Karl Storz Service Manual

January 05, 2010 02:01

Hi Laiq,
Did you get the service manual?.
I have a xenon Nova in Peru that is not working, this equipment works in a poor people Hospital so it´s important to me to get this manual too.
Thanks,

Log inor Register

to rate and post a comment

(10)

HUMBERTO MACHADO

Re: Xenon Nova 20131520, Karl Storz Service Manual

August 27, 2011 10:31

I need this service manual Xenon Nova 20131520!
please send me hmachadomoura@ig.com.br

thanks!!

Log inor Register

to rate and post a comment

(7)
(2)

Victor Kolchenko

Re: Xenon Nova 20131520, Karl Storz Service Manual

October 11, 2011 01:11

Hi, what's the problem with the unit? It's so simple, that almost impossible to be something wrong. I'm former service engineer from KS and have been repaired such devices several times.
tell me what it does (or what it doesn't) and I'll try to help.
Victor

Log inor Register

to rate and post a comment

(6)

jatin joshi

Re: Xenon Nova 20131520, Karl Storz Service Manual

January 17, 2012 09:31

Hi Humberto Machado
I have storz telicame singal chip camera cable
PCB canecter (canect to Camera cansol)Pin NO 4 (UP) mark side is No canect to any canecter .My cable is defectiv you Know about cable canection?
Jatin joshi
india

Log inor Register

to rate and post a comment

(1)

edson amadeu

Re: Xenon Nova 20131520, Karl Storz Service Manual

March 28, 2012 03:04

Hi, I have this unit with a problem, the unit starts but the lamp don´t start.I have measure all diodes, and transistors , but cannot find the problem.The suplly is ok(153v), and the supply of Ic`s are in 5v.
Please can you help me?

Thanks

Log inor Register

to rate and post a comment

(39)
(3)

Holger Fritze

re: Re: Xenon Nova 20131520, Karl Storz Service Manual

November 26, 2013 03:19

Dear edson, the problem can be 2 defective capacitors, i had this a few times. They are in ignition-circuit, blue, 2,2nf, 7500V. Rework isolations arround after changing!
good luck. Holger

Log inor Register

to rate and post a comment

(50)
(3)

Joseph Hughes

re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual

November 08, 2014 09:39

Hello Holger,
I pulled those 2 caps, and they tested OK on my meter, but I am ordering 2 new ones anyways.
So here is a question... The 2 diodes near those caps, what are they? Both of mine seem open. They only have a numerical marking of 72 with 2 dots under them. Their component number are D601 and D602. But I still cant get a manual :( so I do not have access to a schematic that might say more

Log inor Register

to rate and post a comment

(39)
(3)

Holger Fritze

re: re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual

November 10, 2014 10:38

Dear Joseph, i didnt have defective diodes in the ignition-circuit till now. The diodes are high-voltage-types and you cant test with normal diode-tester, with this they are open, but i think they are o.k. There exists 2 or 3 different boards from xenon175. One type has a diac and a diode. Last week i had the first time a defective ignition-transformer. You have to measure an secondary side of the transformer with a high-voltag-probe. The ignition-voltage must be higher 5000V. in my case ist was only 3000 V and there was no ignition. good luck

1 person liked this
Log inor Register

to rate and post a comment

(50)
(3)

Joseph Hughes

re: re: re: re: Re: Xenon Nova 20131520, Karl Storz Service Manual

November 10, 2014 04:34

alright, Thanks. Also, which one is the ignition-transformer? The one with the big wrappings on it?

Log inor Register

to rate and post a comment

(3)

Gausiano

re: Re: Xenon Nova 20131520, Karl Storz Service Manual

November 22, 2013 09:05

HELLO
Dear Victor,
I need help, could you send me the service manual for Xenon Nova 20131520 ?. I will apreciate this so much.
thanks, in advance.
Luis

Log inor Register

to rate and post a comment

(1)

Vasanth Kumar Gunalan

re: Xenon Nova 20131520, Karl Storz Service Manual

March 07, 2014 11:01

Dear Sir, I have xenon nova 20131520 light source. I have problem with board i guess, when i switch on the light source, fan inside is running but bulb is not glowing, please help me on this.. where might be the problem is? I HOPE YOU WOULD HAVE SEEN THIS KIND OF PROBLEM BEFORE.. AWAITING FOR YOUR REPLY..

Thanks in advance
Kumar

Log inor Register

to rate and post a comment

(50)
(3)

Joseph Hughes

re: Xenon Nova 20131520, Karl Storz Service Manual

October 06, 2014 03:46

I know this is a very old post, but I didn't think I should make a new one on the same subject. Does anyone have the service manual they can email me?
Thanks a bunch if you do!
Joseph

Log inor Register

to rate and post a comment

(39)
(3)

Holger Fritze

re: re: Xenon Nova 20131520, Karl Storz Service Manual

October 07, 2014 05:59

Dear all, i need the service-manual too, please can somebody help us? I have the problem, that the ignition voltage is with 2kv too low, so the lamp doesnt ignite. The capacitors are not the reason in this case (like a few other cases). The Lamp Voltage is with 158 V DC o.k. Perhaps we have a defective ignition-transformer, but i dont have a same part to compare. Thank you Holger

Log inor Register

to rate and post a comment

ISS - Contact Us Today For All Your Contrast Injector Needs: 888-667-1062

Injector Support & Service (ISS) offers telephone technical support, depot repair services, loaner injectors, parts identification and sales, PM tools and PM parts kits for medical contrast injectors.

 

 

 

Access and use of this site is subject to the terms and conditions of our LEGAL NOTICE & PRIVACY NOTICE
Property of and Proprietary to DOTmed.com, Inc. Copyright ©2001-2014 DOTmed.com, Inc.
ALL RIGHTS RESERVED