Hi
I restored original drive image from rescue drive "R" with Linux GE tool. And after activationg software the message appear "Current console version is 106, while minimum required is 107. Update EEPROM ?" Thats strange.
And touch screen dosn't work. Video signal presents on booth monitor and work fine. Buttons, keyboard, trackball work fine, i hear beep when press on buttons. Only touch dosn't working.
The question is if i update console EEPROM from 106 to 107 does it wil brick console or not. How i can dump or store console's EEPROM before update EEPROM.
What do you mean "reload software" ? System restored from "original SW_2007" It havent problem devices in "device manager". I starting TestProgAID.exe. Is starting console test. Slider - works. Beep - works. LIght -works. Keyboard - works. Calibration - not work.
"GetVersion" show ID:0106 E:0000
I think com1(rs232) work fine. Main board of console ver 1.09
What do you mean "reload software" ? System restored from "original SW_2007" It havent problem devices in "device manager". I starting TestProgAID.exe. Is starting console test. Slider - works. Beep - works. LIght -works. Keyboard - works. Calibration - not work.
"GetVersion" show ID:0106 E:0000
I think com1(rs232) work fine. Main board of console ver 1.09
What do you mean "reload software" ? System restored from "original SW_2007" It havent problem devices in "device manager". I starting TestProgAID.exe. Is starting console test. Slider - works. Beep - works. LIght -works. Keyboard - works. Calibration - not work.
"GetVersion" show ID:0106 E:0000
I think com1(rs232) work fine. Main board of console ver 1.09
Thank you. I success repaired original Operation system (Windows 2000 bug. SYSTEM registry hive exided limit of 15MB) And its start fine. But no luck. EEPROM update dialog shows again. After press "UPDATE" button, nothing happens and dialog shows again.
I found what the problem. Someone loaded firmware 1.6 to console. When system starts is request version of console and get answer 106. On console board sticker with 1.09. Some one have right firmware of console?
(1)
Leper
Voluson 730 exp touch problem
May 24, 2018 10:03
Hi
I restored original drive image from rescue drive "R" with Linux GE tool. And after activationg software the message appear "Current console version is 106, while minimum required is 107. Update EEPROM ?" Thats strange.
And touch screen dosn't work. Video signal presents on booth monitor and work fine. Buttons, keyboard, trackball work fine, i hear beep when press on buttons. Only touch dosn't working.
The question is if i update console EEPROM from 106 to 107 does it wil brick console or not. How i can dump or store console's EEPROM before update EEPROM.
to rate and post a comment
(31)
simo elbrami
re: Voluson 730 exp touch problem
May 25, 2018 09:49
Hello, just reload the software....and make sure all the drivers is installed
to rate and post a comment
(1)
Leper
re: re: Voluson 730 exp touch problem
May 28, 2018 10:41
What do you mean "reload software" ? System restored from "original SW_2007" It havent problem devices in "device manager". I starting TestProgAID.exe. Is starting console test. Slider - works. Beep - works. LIght -works. Keyboard - works. Calibration - not work.
"GetVersion" show ID:0106 E:0000
I think com1(rs232) work fine. Main board of console ver 1.09
to rate and post a comment
Serge Filatov
re: re: Voluson 730 exp touch problem
May 28, 2018 10:41
What do you mean "reload software" ? System restored from "original SW_2007" It havent problem devices in "device manager". I starting TestProgAID.exe. Is starting console test. Slider - works. Beep - works. LIght -works. Keyboard - works. Calibration - not work.
"GetVersion" show ID:0106 E:0000
I think com1(rs232) work fine. Main board of console ver 1.09
to rate and post a comment
(1)
Leper
re: re: Voluson 730 exp touch problem
May 28, 2018 10:44
What do you mean "reload software" ? System restored from "original SW_2007" It havent problem devices in "device manager". I starting TestProgAID.exe. Is starting console test. Slider - works. Beep - works. LIght -works. Keyboard - works. Calibration - not work.
"GetVersion" show ID:0106 E:0000
I think com1(rs232) work fine. Main board of console ver 1.09
to rate and post a comment
(10)
(1)
Javier Abdulov
re: Voluson 730 exp touch problem
May 28, 2018 10:45
Hi if you need software we can provide you
to rate and post a comment
(1)
Leper
re: re: Voluson 730 exp touch problem
May 29, 2018 10:07
Thank you. I success repaired original Operation system (Windows 2000 bug. SYSTEM registry hive exided limit of 15MB) And its start fine. But no luck. EEPROM update dialog shows again. After press "UPDATE" button, nothing happens and dialog shows again.
to rate and post a comment
(1)
Leper
re: Voluson 730 exp touch problem
May 30, 2018 09:42
I found what the problem. Someone loaded firmware 1.6 to console. When system starts is request version of console and get answer 106. On console board sticker with 1.09. Some one have right firmware of console?
Photo of console.
https://ibb.co/mu4E8J
to rate and post a comment