I ve got an Acuson 128XP/10 that has a software problem, when switched on it displays message, "software sonopack is not licenced for this transducer" this unit has been working for 16 months only.
You have, probably, lost your encryption strings due to a problem in the CVC batteries.
To solve this, first you need to change the batteries, and then re-enter the encryptions.
You have to enter in the setup (after powering the system, after all the tests, when you can see the probe image on the screen hit CODE+SETUP)
Look for a option named DATE&TIME...
Then you just have to set it right...
You can replace it with any 3-3.9V batteries,like battery on computer mother board.and then you can input encryption strings,if you don't have this code,I can help you to get it at cost $600.normally,you can get it from Siemens if you bought the system from Acuson.
Typical failure due to loss of "encryption codes".
Usually caused by the loss of 2, 3.9v batteries on the CVC board.
Replace the batteries, re-enter the codes (hope you have them) and you are fixed.
ROMAN KASIRYE
Acuson 128XP/10 software problem
July 17, 2008 06:00
I ve got an Acuson 128XP/10 that has a software problem, when switched on it displays message, "software sonopack is not licenced for this transducer" this unit has been working for 16 months only.
anybody with a solution to this problem?
Regards
Roman
to rate and post a comment
Emerson Freire
Re: Acuson 128XP/10 software problem
July 17, 2008 09:27
You have, probably, lost your encryption strings due to a problem in the CVC batteries.
To solve this, first you need to change the batteries, and then re-enter the encryptions.
to rate and post a comment
ROMAN KASIRYE
Re: Acuson 128XP/10 software problem
August 25, 2008 04:42
Hello Emerson,
I managed to get the system working when enetered the codes now i need to configure the date, its reading year 2000, how can i update it?
Roman
to rate and post a comment
Emerson Freire
Re: Acuson 128XP/10 software problem
August 25, 2008 09:22
You have to enter in the setup (after powering the system, after all the tests, when you can see the probe image on the screen hit CODE+SETUP)
Look for a option named DATE&TIME...
Then you just have to set it right...
to rate and post a comment
ROMAN KASIRYE
Re: Acuson 128XP/10 software problem
August 26, 2008 03:14
Hi Emerson,
Thanks its now ok, please do you have a pulser board for SSA-240A.
Roman
to rate and post a comment
Emerson Freire
Re: Acuson 128XP/10 software problem
August 26, 2008 09:46
No, I don´t have it....
to rate and post a comment
ROMAN KASIRYE
Re: Acuson 128XP/10 color doppler missing
September 08, 2008 02:18
Hi Emerson,
You have been of so much help on thsi machine, please my color doppler is missing how can i restore it?thanks
Roman
to rate and post a comment
li ming
Re: Acuson 128XP/10 software problem
July 17, 2008 09:36
This is because the date keep battery is over. You need to replace them and enter code again.
Sam
lxm@egwmed.com
to rate and post a comment
ROMAN KASIRYE
Re: Acuson 128XP/10 software problem
July 18, 2008 03:55
Hello Sam,
Where can i buy the batteries? and how can i obtain the encryption strings?
Roman
to rate and post a comment
li ming
Re: Acuson 128XP/10 software problem
July 18, 2008 09:08
You can replace it with any 3-3.9V batteries,like battery on computer mother board.and then you can input encryption strings,if you don't have this code,I can help you to get it at cost $600.normally,you can get it from Siemens if you bought the system from Acuson.
Sam
to rate and post a comment
ROMAN KASIRYE
Re: Acuson 128XP/10 software problem
August 07, 2008 05:53
Hello Sam,
Please i need these codes but you seem to be at a high end please get them to me at $400 and what guaratee do you give me that they will work?
Thanks
Roman
to rate and post a comment
ROMAN KASIRYE
Re: Acuson 128XP/10 software problem
August 25, 2008 09:45
Sam, where is the date battery found is it diffrent from the ones i have replaced??/
Thanks
Roman
to rate and post a comment
Rick Reed
Re: Acuson 128XP/10 software problem
July 17, 2008 10:26
Typical failure due to loss of "encryption codes".
Usually caused by the loss of 2, 3.9v batteries on the CVC board.
Replace the batteries, re-enter the codes (hope you have them) and you are fixed.
to rate and post a comment
ROMAN KASIRYE
Re: Acuson 128XP/10 software problem
July 17, 2008 12:56
I dont have the batteries and how much do they cost then the encryption codes also .
to rate and post a comment
John Carrubba
Re: Acuson 128XP/10 software problem
August 26, 2008 09:33
look up www.rdbatteries.net they sell your batteries for $35.00 each.Part number is 5727.
to rate and post a comment
ROMAN KASIRYE
Re: Acuson 128XP/10 software problem
August 27, 2008 02:39
Hi John,
Thank you so much for this information.
Regards
Roman
to rate and post a comment