I have a Agfa MG3000 for LR3300 laser camera.It works fine with VSI analog interface board but when M6U is connected nothing comes on keypad but for blinking cursor.the keypad works fine with default setting but as soon as its configured with any modality it stops.
You should configure by software when you change any board of MG3000. VSI is newer than M6U and is easier to configure video signals.
Keypad blinking means board not recognized.
Miguel
thanks for response.we have tried to configure it using software but the moment we select m6u as interface board it stops we have tried it with another M6U board but the result is same.the VME bard coding is also correct.any other suggestion
Did you put together to the M6U the image buffer board and the corresponding jumper (small board) at back side of mother board?
They must work as a kit. VSI board no need these other boards.
mail me directly: miguel@engimed.com
It depend what will you connet it. Analogic or digital, what model of printer, LR3300, LR5200...
And what boads are inside MG3000: Gemini, Amdi Foi...
Software is to configurate the MG3000 itself and signals received.
thanks for answering.
board is 1-gemini,versions : portex=0.07 monitor=3.30 bsp=1.08
cpu type 68040
memory 32Mbutevrtx total-worksize=589824 ifx =196608. i would capture an analogic bw video and, using isolan ethernet capture on pc. i do not know haw to do and if the software is available. thanks giovanni
sunil Kumar
Agfa MG3000
November 01, 2004 12:38
I have a Agfa MG3000 for LR3300 laser camera.It works fine with VSI analog interface board but when M6U is connected nothing comes on keypad but for blinking cursor.the keypad works fine with default setting but as soon as its configured with any modality it stops.
Can someone help
to rate and post a comment
Miguel Galeano
Re: Agfa MG3000
November 01, 2004 06:43
You should configure by software when you change any board of MG3000. VSI is newer than M6U and is easier to configure video signals.
Keypad blinking means board not recognized.
Miguel
to rate and post a comment
sunil Kumar
Re: Agfa MG3000
November 02, 2004 01:39
thanks for response.we have tried to configure it using software but the moment we select m6u as interface board it stops we have tried it with another M6U board but the result is same.the VME bard coding is also correct.any other suggestion
to rate and post a comment
Miguel Galeano
Re: Agfa MG3000
November 04, 2004 12:36
Did you put together to the M6U the image buffer board and the corresponding jumper (small board) at back side of mother board?
They must work as a kit. VSI board no need these other boards.
mail me directly: miguel@engimed.com
to rate and post a comment
giovanni ambrifi
Re: Agfa MG3000
December 16, 2004 04:37
please i have to use an mg 3000 but i don't know what kind of software use .
can you help me? thanks
to rate and post a comment
Miguel Galeano
Re: Agfa MG3000
December 17, 2004 09:09
It depend what will you connet it. Analogic or digital, what model of printer, LR3300, LR5200...
And what boads are inside MG3000: Gemini, Amdi Foi...
Software is to configurate the MG3000 itself and signals received.
to rate and post a comment
giovanni ambrifi
Re: Agfa MG3000
December 17, 2004 11:45
thanks for answering.
board is 1-gemini,versions : portex=0.07 monitor=3.30 bsp=1.08
cpu type 68040
memory 32Mbutevrtx total-worksize=589824 ifx =196608. i would capture an analogic bw video and, using isolan ethernet capture on pc. i do not know haw to do and if the software is available. thanks giovanni
to rate and post a comment
Bao Vo Quoc
Re: Agfa MG3000
June 10, 2010 10:14
Dear my friend,
This MG3000 can capture the Video signal and configuration to DICOM OUT for Drystar3000/ 5300/5302,...
you need to configuration all of them, there are many step to do it,
please contact me if you need the further info
Regards
Vo Quoc Bao
Field Service Engineer
to rate and post a comment