If you have a broken Sonosite, Mindray, GE, Philips, Hitachi, or Aloka system or probe contact us today. Free ultrasound & probe EVALS with 1 Year Warranty on all repairs. We repair all orders in 1-5 days. Call 844-644-5440 Email: Sales@Lenard.Healthcare
farhan zeb
create partition problem in HSA CT/i please help
September 12, 2011 01:32
when i try to label or create partitions with the command boot -f dksc(1,6,8)sashARCS dksc(1,6,7)stand/fx.ARCS --x
the following error occurs
unable to load dksc(1,6,8)sashARCS: no such device
i m preping new OC drive do the disk drive is not labelled thats y error occurs when i try to load software directly so how can i label the hdd drive this command is not working or there is some other problem please help me
to rate and post a comment
Ivano Murat
Re: create partition problem in HSA CT/i please help
September 16, 2011 06:10
Hello Usman,
I'm not directly familiar with the system You're having this problem onto, but it seems to me like we're talking about an SGI computer (maybe O2 or Octane?).
What I can tell You is that is telling You You don't even have the device You're trying to boot from. Maybe You took that boot command from some manual wich is not related to the exact model of system You're working on. My advice is You have a look at the devices available on Your system.
In order to do so, when You switch on the system and the computer is trying to autoboot, stop it by pressing the "ESC" key; this way You should be presented a menu, from wich You should click on the "Command Monitor" (if I remember well); once You're into it (You should see some sort of "DOS Box", let's call it so) type "hinv" (without the quotes, of course) and press enter.
You should now see the hardware configuration of Your computer, similar to this:
CPU: MIPS R5000 Processor Chip Revision: 2.1
FPU: MIPS R5000 Floating Point Coprocessor Revision: 1.0
1 180 MHZ IP32 Processor
Main memory size: 128 Mbytes
Secondary unified instruction/data cache size: 512 Kbytes on Processor 0
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
FLASH PROM version 4.17
Integral SCSI controller 0: Version ADAPTEC 7880
Disk drive: unit 1 on SCSI controller 0 (unit 1)
CDROM: unit 4 on SCSI controller 0
Integral SCSI controller 1: Version ADAPTEC 7880
On-board serial ports: tty1
On-board serial ports: tty2
On-board EPP/ECP parallel port
CRM graphics installed
Integral Ethernet: ec0, version 1
Iris Audio Processor: version A3 revision 0
PCI Adapter ID (vendor 36868, device 32888) pci slot 1
PCI Adapter ID (vendor 36868, device 32888) pci slot 2
Video: MVP unit 0 version 1.4
with no AV Card or Camera.
Vice: TRE
What You're looking for is probably the CDROM line; in my example, it reports I have a CDROM unit with ID 4, linked on the controller n°0. This way, Your boot line would become the following:
boot -f dksc(0,4,8)sashARCS dksc(0,4,7)stand/fx.ARCS --x
Hope this can help You out in any way. Please feel free to contact me at technosystems_srl@libero.it , should You need any further assistance.
Best regards,
Ivano Murat
to rate and post a comment
farhan zeb
Re: create partition problem in HSA CT/i please help
September 17, 2011 07:12
thanks IVANO
1_) i have loaded the software first i loaded the OS then
Applications and after that i have to configure or load the SBC with OC when i type the command loadSBC so the
following error occurs Not enough free spcae can not load network software
when i try to connect to SBC i type the command cu sbc but following error occured connect failed: cant't access
device
i have tried all the procedure from LFC but still same problem i have tried to bring it to the MC6080> prompt but
still nothing happened still same problem
but when i use the command rsh sbc and reconfig the sbc and after st so during initialization system goes shut down
itself .
NOTE:
when i have loaded the application software so after that when i open the unix shell so an message
appeared executing install.dasm no dasm's found
so please help me i'll wait for your reply
2_) Dear friend i have lost the system state also of cti indigo2 system and and the oc disk drive have been crashed
i have
replace the disk drive and loaded the software from cold so i have lost my system state so now i have loaded the
software but i have no system state but there is need of the system state so what should i do now there is the
method to restore files in the LFC but how should i access the unix shell with crash disk drive so please tell me
what will be the alternative way to skip this step and start the applications.
to rate and post a comment
farhan zeb
Re: create partition problem in HSA CT/i please help
September 17, 2011 07:12
I HAVE INDIGO2 system
to rate and post a comment
bens prado
Re: create partition problem in HSA CT/i please help
September 22, 2011 10:16
good day
I have a problem like that recently in cti indigo
Please change your sbc hard dsik
since there are two disk in sbc change the one with applications
to rate and post a comment
farhan zeb
Re: create partition problem in HSA CT/i please help
September 26, 2011 05:38
ok thnx the problem is solved
to rate and post a comment
Ronald
re: Re: create partition problem in HSA CT/i please help
January 20, 2013 01:35
Hi Farhan, how you solve the problem?, I had similar problem, I used new HDD from 3rd party, I heard if we buy HDD from GE will no problem ,cause already initialize and formated, I read on SGI webs, that we need "fx" tools to do that but how we can get that?.thanks
to rate and post a comment
salman khan
re: re: Re: create partition problem in HSA CT/i please help
January 20, 2013 11:35
Hello Ronald
Email me at salmankhan.ge.ct@gmail.com may be i will have a solution for you.
to rate and post a comment