Hello all. A problem with HDI 5000 - at replacement FEC and PSM the device began to give out the message at loading:
Alert
An error has been detected Please record the following information and call ATL TechSupport Date: 12/21/2008 Time: 19.13.43
Diagnostics Number:0002
thus any key of the keyboard does not work. To clean this window according to the service description and to look the following message. Superkey+6 Superkey+0 do not work. Prompt what to make? Many thanks.
Try superkey Frame Rate to clear the banner. You will need to go into the software by typing username "csr" and password "user" to go into configuration and select "save as installed".
Thanks, after long meditations and unsuccessful attempt to clean a banner the problem was solved replacement flash microcircuits from old FEC in new... All thanks.
Greetings all over again disconnect gauges. Most likely does not work the controller of the gauge. If the mistake will not leave try to update a configuration of the equipment.. It is not hardware. If service a manual is necessary - write. If any changes - send a broad gully and sreens - we shall understand all together.. Success
I had that issue several times and most of the times 0002 error was caused by the PSM did you verify that the PSM is working correctly in another ATL 5000?
I replaced the module with a new one PSM and equipment worked properly for 72 hours. the fourth day get error 002 service checking mode power subsystem to check voltages aparecce -HV ovolt but at the same time I measure with multimeter test points and there 110volt psm. and 3.3 volt voltage regiatra not. my question is that frontend board be failing. channel- FEC- or AIM. thank you
dear all,
I have error code 0089 blue colored in my atl 5000. It appears 10-12 minutes after doing usg. What is the reason and what should I do for this.
Greetings all over again disconnect gauges. Most likely does not work the controller of the gauge. If the mistake will not leave try to update a configuration of the equipment.. It is not hardware. If service a manual is necessary - write. If any changes - send a broad gully and sreens - we shall understand all together.. Success
Igor Solopov
Error code ATL 5000
December 21, 2008 10:54
Hello all. A problem with HDI 5000 - at replacement FEC and PSM the device began to give out the message at loading:
Alert
An error has been detected Please record the following information and call ATL TechSupport Date: 12/21/2008 Time: 19.13.43
Diagnostics Number:0002
thus any key of the keyboard does not work. To clean this window according to the service description and to look the following message. Superkey+6 Superkey+0 do not work. Prompt what to make? Many thanks.
to rate and post a comment
Bill Decker
Re: Error code ATL 5000
December 21, 2008 07:18
Try superkey Frame Rate to clear the banner. You will need to go into the software by typing username "csr" and password "user" to go into configuration and select "save as installed".
to rate and post a comment
Igor Solopov
Re: Error code ATL 5000
December 22, 2008 01:02
Thanks, after long meditations and unsuccessful attempt to clean a banner the problem was solved replacement flash microcircuits from old FEC in new... All thanks.
to rate and post a comment
MOHAMED KHALIL
Re: Error code ATL 5000
March 21, 2009 01:21
Hi
I have the same Error at my atl5000
I have to change the channel board?
the power supply is ok
thx
to rate and post a comment
Igor Solopov
Re: Error code ATL 5000
March 22, 2009 02:51
Greetings all over again disconnect gauges. Most likely does not work the controller of the gauge. If the mistake will not leave try to update a configuration of the equipment.. It is not hardware. If service a manual is necessary - write. If any changes - send a broad gully and sreens - we shall understand all together.. Success
to rate and post a comment
pavel khaziniuk
Re: Error code ATL 5000
March 23, 2009 12:54
I had that issue several times and most of the times 0002 error was caused by the PSM did you verify that the PSM is working correctly in another ATL 5000?
to rate and post a comment
Carlos Klein
re: Re: Error code ATL 5000
August 26, 2014 10:12
I replaced the module with a new one PSM and equipment worked properly for 72 hours. the fourth day get error 002 service checking mode power subsystem to check voltages aparecce -HV ovolt but at the same time I measure with multimeter test points and there 110volt psm. and 3.3 volt voltage regiatra not. my question is that frontend board be failing. channel- FEC- or AIM. thank you
to rate and post a comment
RIZWAN UPPAL
Re: Error code ATL 5000
November 21, 2009 04:10
dear all,
I have error code 0089 blue colored in my atl 5000. It appears 10-12 minutes after doing usg. What is the reason and what should I do for this.
to rate and post a comment
Murat Canpolat
Re: Error code ATL 5000
November 21, 2009 06:38
we need to introduce new board plugged into the system is dense.
to rate and post a comment
Antonio Pisciotta
Re: Error code ATL 5000
September 20, 2010 08:21
I have the same problem on my HDI 5000; have you solved it?
Can you give some information about this error?
Is the DVS board? Do you change it?
Thanks very much, Antonio
to rate and post a comment
Igor Solopov
Re: Error code ATL 5000
March 22, 2009 08:13
Greetings all over again disconnect gauges. Most likely does not work the controller of the gauge. If the mistake will not leave try to update a configuration of the equipment.. It is not hardware. If service a manual is necessary - write. If any changes - send a broad gully and sreens - we shall understand all together.. Success
to rate and post a comment
Antonio Pisciotta
Re: Error code ATL 5000
January 28, 2011 08:58
Hello, what can i do to enter in service mode and than insert username and pwd in HDI 5000?
Thanks
to rate and post a comment