Hello everyone,
I had a problem with the graphics card. I replaced it with a new nvidia quadro nvs285 and I installed the drivers. While I was doing the BIOS reset due to low voltage on the battery. I replaced the battery and set the BIOS as specified in the service documentation. Now when you turn Iconos R200, turn on automatically Fluorospot but will not turn on and Polydoros. I do not understand what happened but when you turn off fluorospot my Polydoros is started after a few seconds and displays my error 007/16. Perhaps the BIOS was set differently in relation to documentation? All cables'm back in place and in accordance with the service documentation. Please help me fix this problem.
Yes, 007/16 error means that there is no communication between the camera and XCU. When you start Iconos R200 on XCU an error is 1 (small display on XCU). This is probably because the system is not ready. When you turn off the FLC (turn off the computer with the power button) polidoros is started automatically and error "fluorospot not ready" which is normal because it is turned off. Now on display at XCU error is 5. In normal operation in this display stands 6 if everything is OK.
I think that all of the equipment is properly working. Everything was in perfect until he died graphics card and reset the bios. You may be missing some condition from the bios to the system started normally.
Why is polidoros start when you turn off the PC? It makes me that everything is probably Setting BIOS.
DirectMed Imaging specializes in Equipment Sales, Parts, and Support. Parts are in stock and available for immediate delivery. In-room MRI Upgrades are available now. (855) 463-3727 or sales@directmedimaging.com
Darko Savic
ICONOS R200 problem
December 07, 2014 12:12
Hello everyone,
I had a problem with the graphics card. I replaced it with a new nvidia quadro nvs285 and I installed the drivers. While I was doing the BIOS reset due to low voltage on the battery. I replaced the battery and set the BIOS as specified in the service documentation. Now when you turn Iconos R200, turn on automatically Fluorospot but will not turn on and Polydoros. I do not understand what happened but when you turn off fluorospot my Polydoros is started after a few seconds and displays my error 007/16. Perhaps the BIOS was set differently in relation to documentation? All cables'm back in place and in accordance with the service documentation. Please help me fix this problem.
Thank you in advance.
to rate and post a comment
Lenny Place
re: ICONOS R200 problem
December 08, 2014 06:10
do you have the bios reset cd if not what software version do you have and computer type?
to rate and post a comment
Darko Savic
re: re: ICONOS R200 problem
December 09, 2014 11:53
No, I do not have bios cd. Maybe I can download bios for a floppy drive from the website. Bios version of the FLC is V5.00 Rev. R1.03.1858
to rate and post a comment
Lenny Place
re: ICONOS R200 problem
December 08, 2014 06:10
what the error 007/16 means is the camera in not communicating with the XCU
to rate and post a comment
Darko Savic
re: re: ICONOS R200 problem
December 09, 2014 11:53
Yes, 007/16 error means that there is no communication between the camera and XCU. When you start Iconos R200 on XCU an error is 1 (small display on XCU). This is probably because the system is not ready. When you turn off the FLC (turn off the computer with the power button) polidoros is started automatically and error "fluorospot not ready" which is normal because it is turned off. Now on display at XCU error is 5. In normal operation in this display stands 6 if everything is OK.
I think that all of the equipment is properly working. Everything was in perfect until he died graphics card and reset the bios. You may be missing some condition from the bios to the system started normally.
Why is polidoros start when you turn off the PC? It makes me that everything is probably Setting BIOS.
Any suggestion is welcome.
to rate and post a comment
Lenny Place
re: re: re: ICONOS R200 problem
December 10, 2014 08:37
Darko
please give me an email address and I will send you the Bios Settings for the FLC v5.0
to rate and post a comment
Darko Savic
re: re: re: re: ICONOS R200 problem
December 10, 2014 11:32
My email is savic.net@hotmail.com
to rate and post a comment