I am working on a GE LS4 CT which cannot boot the IG1 via network boot, there's no problem in the IG because i can manually boot the IG by pressing the power switch. I already connect monitor and keyboard and enable the network boot in IG. but still the IG1 is not booting up via network
Put monitor on DARC and watch it boot, at a certain spot it will boot the IG, see if it fails to boot the IG. Perhaps software on DARC needs to be reloaded or perhaps IG needs to be power cycled with Darc completely up to get IP address from DARC.
Check if You have an IG1 set in recofing.
If Yes and it boots manually then check the LAN cable and Network adapter.
Try to boot IG module manually and then try co connect to it via "telnet localhost 623" command.
When it works properly then something is wrong with the DARC or IG BIOS settings. Verify them.
Good Luck
The Software 04MW11.16 i'm using have no IG reconfig setup in the hardware tab. The lan cable is working fine that I can ping the IG when i press the power switch. And about the "telnet localhost 623" this command is having an error when i try to reset the console "reset -c" "reset -console". Both commands is not properly working.
Brand new OEM Philips & Siemens Parts at unbeatable prices shipping domestically and Includes warranty!
Email P/N for pricing: sales@Relaxationinc.com
(P) 813-925-1314, www.relaxationinc.com
Ken
IG booting UP Problem
December 15, 2015 08:15
I am working on a GE LS4 CT which cannot boot the IG1 via network boot, there's no problem in the IG because i can manually boot the IG by pressing the power switch. I already connect monitor and keyboard and enable the network boot in IG. but still the IG1 is not booting up via network
Please Help. Thank you in advance.
to rate and post a comment
Brent Hull
re: IG booting UP Problem
December 16, 2015 08:52
Check the bios settings for the DARC and IG.
to rate and post a comment
Ken
re: re: IG booting UP Problem
December 17, 2015 09:11
Bios of DARC and IG is okay. I already enable the wake up lan for IG.
to rate and post a comment
JB
re: IG booting UP Problem
December 16, 2015 03:37
Put monitor on DARC and watch it boot, at a certain spot it will boot the IG, see if it fails to boot the IG. Perhaps software on DARC needs to be reloaded or perhaps IG needs to be power cycled with Darc completely up to get IP address from DARC.
to rate and post a comment
Ken
re: re: IG booting UP Problem
December 17, 2015 09:11
I noticed upon DARC boot up, when its trying to Bring up the interface of eth0, until the application software is up, the IG is still not booting up.
to rate and post a comment
Pawel Kopysc
re: IG booting UP Problem
December 16, 2015 03:38
Hi,
Check if You have an IG1 set in recofing.
If Yes and it boots manually then check the LAN cable and Network adapter.
Try to boot IG module manually and then try co connect to it via "telnet localhost 623" command.
When it works properly then something is wrong with the DARC or IG BIOS settings. Verify them.
Good Luck
to rate and post a comment
Ken
re: re: IG booting UP Problem
December 17, 2015 09:11
Hello,
The Software 04MW11.16 i'm using have no IG reconfig setup in the hardware tab. The lan cable is working fine that I can ping the IG when i press the power switch. And about the "telnet localhost 623" this command is having an error when i try to reset the console "reset -c" "reset -console". Both commands is not properly working.
to rate and post a comment
Pawel Kopysc
re: re: re: IG booting UP Problem
December 17, 2015 06:07
Try to reload the software on DARC. Can be a software issue
to rate and post a comment
Ken
re: re: re: re: IG booting UP Problem
December 18, 2015 08:55
Done Reloading software on DARC. Still the problem Exist.
to rate and post a comment
Pawel Kopysc
re: re: re: re: re: IG booting UP Problem
December 20, 2015 10:40
In my opinion there is a problem with Network Adapter on IG. You can ping from DARC to IG.
Confirm that You have tried with this commands:
{ctuser@darc} or [root@darc]
telnet localhost 623
Server: ig1
Username:
Password:
Login successful
dpccli> reset
ok
console
If this is not working porperly then i will first replace IG module
to rate and post a comment