We offer reliable & cost-effective spare parts for the Philips Achieva 1.5T MRI system helping you minimize downtime & keep operations smooth. Wide inventory available. Quick turnaround time. Expert support. Worldwide delivery. Contact Limor@elsmed.com
marivic
kodak8700
October 20, 2013 09:49
i am getting an error 509 on our kodak8700 dryview printer.can you help us solve the problem
to rate and post a comment
Sayat Karapetyan
re: kodak8700
October 21, 2013 07:59
If the drum temperature is below 122.25°C, P511 Processor warming , xx minutes until ready is
displayed. If the processor does not warm up in the time calculated by the SCB (and displayed on the
local panel), EC509 Processor failed to warm up in allotted time is generated. The top cover must be
lifted to clear this error.
to rate and post a comment
Lenny Place
re: kodak8700
October 21, 2013 02:37
7-6-56. EC509: Processor failed to warm up in allotted time
Local Panel Message HQ Keypad Message Error Log OMX IM 952 Host alarm
Printer malfunction.
P509
K202: Laser imager X
is not operational.
L509
PROCESSOR_WARMUP_FAIL
ALM,17
Summary
If the drum temperature is below 122.25°C, P511 Processor warming , xx minutes until ready is
displayed. If the processor does not warm up in the time calculated by the SCB (and displayed on the
local panel), EC509 Processor failed to warm up in allotted time is generated. The top cover must be
lifted to clear this error.
Phone Fix – Operator Correctable
On Site – Technician Correctable
1. Problem: EC 552 or EC 553. Slow warm up/drum heater fail.
Cause: Heater fuse is blown. The current fuses are known to have about a 3 to 4 year life before they
fail due to age. A new style fuse is being redesigned.
Note
Some of the early IMAGER’s did not have the connection clip soldered to the fuse leads. This
created a poor connection with resultant premature failure of the fuses.
Solution: If a fuse has failed due to age, replace all three fuses. Refer to Service Manual disassembly
section. Solder connection clips to the fuse leads using a heat sink to keep the heat away from the
fuse.
2. Problem: EC 551/552/553. Rotating Processor Boards blowing.
Cause: Heat sink for transistor is not mounted correctly, causing the transistor to burn out.
Solution: Order a new RPB, and inspect the new board to ensure that the transistor is sandwiched
between the two heat sinks.
to rate and post a comment
marivic
re: re: kodak8700
October 24, 2013 01:38
from solution number 1, can you locate where are the fuse need to replace?please give me idea where i can find it in the manual?
to rate and post a comment
marivic
re: re: kodak8700
October 30, 2013 09:19
i already read the service manual.. it says if you replace or remove the rpb board or the heater drum you need to do some adjustment using the mpc software, i dont have this kind of software.
to rate and post a comment
Gilrubio
re: kodak8700
October 21, 2013 02:38
Turn on the processor, wait few minutes, lift the top cover, open the drum cover.
Carefully (very carefully) touch the drum.
If the drum is cold, probably the internal temperature fuse is blown
to rate and post a comment
marivic
re: re: kodak8700
October 24, 2013 01:38
if the fuse is blown in the drum, can we replace the fuse or do we need to change the whole drum?
to rate and post a comment
Sayat Karapetyan
re: re: re: kodak8700
October 24, 2013 11:57
Give me your e-mail to send you a service manual for Kodak 8700.There you will find the answers to all your questions.
Regards,
Sayat
e-mail:sayat1956@gmail.com
to rate and post a comment
Lenny Place
re: re: re: kodak8700
October 24, 2013 11:58
I have replaced them in the past they a thermal fuses I would have to check when I get home to see what the temperature rating is.
to rate and post a comment
Lenny Place
re: re: re: kodak8700
October 30, 2013 04:43
I can send you the MPC software, and instructions on installation
to rate and post a comment
marivic
re: re: re: re: kodak8700
October 31, 2013 01:00
please send me the software...thanks in advance
to rate and post a comment
Lenny Place
re: re: re: re: re: kodak8700
October 31, 2013 05:22
I am sending please read the instructions in the hardlock removal folder
to rate and post a comment
sergey bunin
re: re: re: re: kodak8700
March 29, 2014 09:03
please send me the software...thanks in advance.
My email: ooovgva@gmail.com
to rate and post a comment
Jose Eduardo Martinez
re: kodak8700
October 25, 2013 02:35
did you fix the problem? seasbi@hotmail.com I speak english and spanish
to rate and post a comment