We provide sales, service, rental, and repair for ultrasound systems, probes, and C-arms. We have the largest inventory in the world. Contact us about our special offers on certified refurbished equipment! Call: 317-759-9210 Email: sales@probomedical.com.
Humayun Khan
LOGIQ 7 Boot up issue
August 15, 2013 05:43
Hello,
I've BT'03 CRT LOGIQ 7
Not booting up, there is LOGIQ GE Splash screen and progress bar keep on moving
TGC LED's are ON
Tried to reset, BE & FE Cable, HDD Cable
But still the same
System was completely off and stored for almost 5 months.
During First Start up there is message "Unable to find Floppy Drive Press F1 to proceed or Del to go to setup, If I go to BIOS to change the boot order from Floppy to HDD0, doesn't save the changes then system restart and I have to Press F1 again to proceed.
System was working fine and able to get into imaging before it was stored five months back
Any comments will be appreciated
Regards
to rate and post a comment
Rey Gonzalez
re: LOGIQ 7 Boot up issue
August 16, 2013 10:08
Check BIOS battery, HD and if you have a BIOS blaster CD try it restore them.
Good luck rey@allultrasoundservices.com
to rate and post a comment
Pracha Yang
re: re: LOGIQ 7 Boot up issue
August 17, 2013 10:38
Like Rey said, check your BIOS battery, since it keeps asking you for setup. It should be at least 3V.
For the system not booting, I would try to disconnect the front end from the back end. There's a wide grey ribbon cable going from the back end to the front end. Disconnect that cable and power to the front end to see if the system boots up all the way. If it does boot up all the way, then your front end may be causing the system to hang at the loading screen.
If your system still hangs at loading, then the issue may be in your back end processor. Check your voltages from the back end power supply to see if they aren't being loaded down. Also, make sure all fans in the BEP is working.
Conquest Imaging - Because Quality Matters
866-900-9404
pyang@conquestimaging.com
to rate and post a comment
Humayun Khan
re: re: re: LOGIQ 7 Boot up issue
August 17, 2013 09:44
Thanks Rey, Pracha Marcelo for your help.
I have replaced the BIOS Battery
I disconnected the wide gray ribbon cable from FE (MDBRG Board) and rebooted the system, it still hangs on LOGIG loading screen with progress bar and Dos windows popping up and disappearing
to rate and post a comment
Roberto Hernandez
re: re: re: LOGIQ 7 Boot up issue
September 01, 2017 08:13
Hi Yang, can you please send me the SW and aplication software for the Logiq 7?
I have to reinstall the software base and aplication software.
I'll really appreciate it if you send me the software for the Logiq 7. My email is rahp82@gmail.com
Thanks
to rate and post a comment
Humayun Khan
re: re: LOGIQ 7 Boot up issue
August 17, 2013 09:44
Thanks Rey, Pracha Marcelo for your help.
I have replaced the BIOS Battery
I disconnected the wide gray ribbon cable from FE (MDBRG Board) and rebooted the system, it still hangs on LOGIG loading screen with progress bar and Dos windows popping up and disappearing
to rate and post a comment
Marcelo Antonio Correa
re: LOGIQ 7 Boot up issue
August 17, 2013 10:41
Hi, Humayun! I agree with Rey. But, I'd like to suggest you to take the BEP and all its internal boards off and installing a regular HDD and some other OS, intending to check if the BEP works as a normal PC. Other: you said you reset the SCSI cable between PC2IP and FEC boards. You might have or PC2IP either FEC, or both boards defective (those could cause the boot to stop - check a red LED on FEC board during the boot). This L7 was stored for a long time, it's possible that a simply PM could take it back on air. Try this, first, let us know the outcome, alright? Take care, God Bless. MAC.
to rate and post a comment
Humayun Khan
re: re: LOGIQ 7 Boot up issue
August 17, 2013 09:44
Thanks Rey, Pracha Marcelo for your help.
I have replaced the BIOS Battery and able to save the changes.
I disconnected the wide gray ribbon cable from FE (MDBRG Board) and rebooted the system, it still hangs on LOGIG loading screen with progress bar and Dos windows popping up and disappearing
to rate and post a comment
Roberto Hernandez
re: re: LOGIQ 7 Boot up issue
September 01, 2017 08:13
Hi Marcelo, can you please send me the SW and aplication software for the Logiq 7?
I have to reinstall the software base and aplication software.
I'll really appreciate it if you send me the software for the Logiq 7. My email is rahp82@gmail.com
Thanks
to rate and post a comment
Humayun Khan
re: LOGIQ 7 Boot up issue
August 17, 2013 09:44
Thanks Rey, Pracha Marcelo for your help.
I have replaced the BIOS Battery
I disconnected the wide gray ribbon cable from FE (MDBRG Board) and rebooted the system, it still hangs on LOGIG loading screen with progress bar and Dos windows popping up and disappearing
to rate and post a comment
Marcelo Antonio Correa
re: re: LOGIQ 7 Boot up issue
August 19, 2013 03:55
If you have the Base Image Load System (Ghost) and the App SW Disk, maybe, it's time to reinstall all over and give the HDD a fresh and clean OS. Take care, good luck, God Bless. MAC.
to rate and post a comment
Humayun Khan
re: re: re: LOGIQ 7 Boot up issue
September 02, 2013 09:50
if any one of you have Application SW 2.X.x OR 3.x.x I would appreciate. This LOGIQ 7 has BEP 2 PN 2372267 (R2.1.1). Thanks for help
to rate and post a comment
Bayanzul Batsukh
re: re: re: re: LOGIQ 7 Boot up issue
September 25, 2013 02:47
Humayan I ve got exactly same problem with L7 , it has been unplugged for almost a year,
I was wondering did you fix the problem yet ?
to rate and post a comment
Roberto Hernandez
re: re: re: re: re: LOGIQ 7 Boot up issue
September 01, 2017 08:13
Hi, can you please send me the SW and aplication software for the Logiq 7?
I have to reinstall the software base and aplication software.
I'll really appreciate it if you send me the software for the Logiq 7. My email is rahp82@gmail.com
Thanks
to rate and post a comment
Bayanzul Batsukh
re: re: re: re: LOGIQ 7 Boot up issue
September 25, 2013 02:47
I ve got exactly same problem same situation , did you fix the L7 yet please share?
to rate and post a comment
Humayun Khan
re: re: re: re: re: LOGIQ 7 Boot up issue
October 04, 2013 01:43
Hello Bayanzul,
Try reloading SW.Both first Base then Appliction, make sure SW Level should be the same what you have right now on the system.
I'm stuck because I don't have BT'03 Application SW Disk. I'm looking for it hope fully If some one has it I would appreciate.
Try and let me know if it fix the issue
to rate and post a comment
Zach Ruder
re: LOGIQ 7 Boot up issue
October 03, 2013 06:26
I have had the power supply also cause booting issues. Make sure and check power supply voltages.
to rate and post a comment
Roberto Hernandez
re: re: LOGIQ 7 Boot up issue
September 01, 2017 08:13
Hi, can you please send me the SW and aplication software for the Logiq 7?
I have to reinstall the software base and aplication software.
I'll really appreciate it if you send me the software for the Logiq 7. My email is rahp82@gmail.com
Thanks
to rate and post a comment
Roberto Hernandez
re: LOGIQ 7 Boot up issue
September 01, 2017 08:13
Hi , can you please send me the SW and aplication software for the Logiq 7?
I have to reinstall the software base and aplication software.
I'll really appreciate it if you send me the software for the Logiq 7. My email is rahp82@gmail.com
Thanks
to rate and post a comment
TECNOMEDICS
re: re: LOGIQ 7 Boot up issue
July 01, 2018 12:48
good afternoon friends of dotmed, I need the software for logiq 7 version 2 this is my email wyllc2000@gmail.com
to rate and post a comment
Jesus E Mendez
re: LOGIQ 7 Boot up issue
December 29, 2017 04:57
Hi. I have the same problem but I dont know why all USB port are disable and I cant use the service dongle. My system stop on GE white screen when try to fill the blue bar. I tried to swap the HDD and used another CD-Drive to boot the software reload but not working. Anybody can help me. Sorry, I dont know how I can post my own question, but I see that you have a similar issues with your system
to rate and post a comment
TECNOMEDICS
re: LOGIQ 7 Boot up issue
July 02, 2018 06:41
Good afternoon, I need that version of the software. Thank you. This is my e-mail.
to rate and post a comment