Hello,
Some body knows configured the system after replace NV RAM on polydoros LX 50
I replace the NV RAM, I bough this from USA and I thing pull out the other system.
replace full D200 but system not working, and then only replace the NV RAM, the system now working but not move grid on table.
only rot stator not shut RX
Ths side structure had options with exposure from KK interface, I marked this option and reboot system and try exposure but not rot no nothing
Thanks
You need a PC with serial port and the XCS service software installed on it. If you have backup floppy and XCU download disk you can restore the system to original.
Without the Backup diskette you have to configure the system through the service program.
tibor@ivanszky.com
So I have the old NVRAM
install again and then make a bachup site structure
Do then replace NVRAM and only download by XCU with other NVRAM?
always I do this procedure but no enable the move Grid
I saw on dotmed that you have manuals for LX polydoros, I have a problem in d200 I need to configure but , I can´t connect with my two laptops , one is with xp win and the other with 3.11 .
I checked tha cable but I don´t have the exact config , I changed the D200 and the problem is the same gen stops in 2 on display of D100
Do you have the excat config of the service cable , and the com1 parameters on com1 .
We supply high-quality refurbished and used imaging equipment and parts to hospitals, imaging centers, and brokers worldwide. We pay top dollar and offer installation, deinstallation, service, and transport. Se habla español info@medilabglobal.com
Germni
NV RAM Polydoros LX Replace
April 08, 2019 10:28
Hello,
Some body knows configured the system after replace NV RAM on polydoros LX 50
I replace the NV RAM, I bough this from USA and I thing pull out the other system.
replace full D200 but system not working, and then only replace the NV RAM, the system now working but not move grid on table.
only rot stator not shut RX
Ths side structure had options with exposure from KK interface, I marked this option and reboot system and try exposure but not rot no nothing
Thanks
to rate and post a comment
juan pablo amado
re: NV RAM Polydoros LX Replace
April 09, 2019 10:24
reload site config by XCS soft. O try reinstall old NVRam, make a backup site data to a floppy, and the replace nvram
to rate and post a comment
Tibor Ivanszky
re: NV RAM Polydoros LX Replace
April 09, 2019 10:25
You need a PC with serial port and the XCS service software installed on it. If you have backup floppy and XCU download disk you can restore the system to original.
Without the Backup diskette you have to configure the system through the service program.
tibor@ivanszky.com
to rate and post a comment
Germni
re: re: NV RAM Polydoros LX Replace
April 10, 2019 08:58
So I have the old NVRAM
install again and then make a bachup site structure
Do then replace NVRAM and only download by XCU with other NVRAM?
always I do this procedure but no enable the move Grid
to rate and post a comment
Sergio Garcia Solana
re: re: re: NV RAM Polydoros LX Replace
May 07, 2019 10:01
Hi Sir,
I saw on dotmed that you have manuals for LX polydoros, I have a problem in d200 I need to configure but , I can´t connect with my two laptops , one is with xp win and the other with 3.11 .
I checked tha cable but I don´t have the exact config , I changed the D200 and the problem is the same gen stops in 2 on display of D100
Do you have the excat config of the service cable , and the com1 parameters on com1 .
Best regards and thank you in advance
Sergio
to rate and post a comment