I got problems with PQS, since it can't turn drivers on. Panel Service Driver Led is off, Gantry can't rotate or tilt & table can't move (V/H), and a few fault signals are turned on(Analog Cont, ACInput, Inverter & Relay) I have 480V in CRX200 module and the brushes are OK, the signals MDSTR & GP on PMDC are such that the K306 and K307 are not energized.
I don't know either GPU or Gantry module is failling.... Thank you
I am a certified Picker Engineer . I can come to fix your system . If u r still interested , please contact me at my e-mail : abdusaed@link.net or mobile phone :+2012-2889193
How did you fixed the problem?,... I have the same situation on PQS CT. I have checked every think, but no any good look,
All that I can see on the Console is that No comunication exist with
XSC and GPU. I did gxd command and it seen that the procedure
was completed 100% with out error for both XSC and GPU.
Many thanks,
,
Miguel A. Lemus
BIOMEL, S.A. de C.V.
25 calle pte #1254
Col. Layco, San Salvador
El Salvador.
Tel: +503 2226 5599
Fax: +503 2211 5380
Cell phone:+503 7982 6431
Email : biomel@navegante.com.sv
biomedicalemus@gmail.com
GCI offers complete MRI & CT sales & service with ROI analysis, in-house financing, contractor drawings, accreditation, training, marketing, and OEM-level support beyond the sale.
Manuel Esquer
PICKER PQS Drivers problem
May 02, 2005 07:01
I got problems with PQS, since it can't turn drivers on. Panel Service Driver Led is off, Gantry can't rotate or tilt & table can't move (V/H), and a few fault signals are turned on(Analog Cont, ACInput, Inverter & Relay) I have 480V in CRX200 module and the brushes are OK, the signals MDSTR & GP on PMDC are such that the K306 and K307 are not energized.
I don't know either GPU or Gantry module is failling.... Thank you
to rate and post a comment
gustavo fiochi
Re: PICKER PQS Drivers problem
May 03, 2005 07:48
may be the gpu is not runnig. check the leds during the turn on secuence;
to rate and post a comment
Manuel Esquer
Re: PICKER PQS Drivers problem
May 03, 2005 12:10
What should I see on leds?
to rate and post a comment
Abdula Saeed El Shafeey
Re: PICKER PQS Drivers problem
July 13, 2005 12:51
I am a certified Picker Engineer . I can come to fix your system . If u r still interested , please contact me at my e-mail : abdusaed@link.net or mobile phone :+2012-2889193
Good luck
Abdullah
to rate and post a comment
Miguel Angel Lemus
Re: PICKER PQS Drivers problem
February 26, 2009 06:21
Hi Manuel,
How did you fixed the problem?,... I have the same situation on PQS CT. I have checked every think, but no any good look,
All that I can see on the Console is that No comunication exist with
XSC and GPU. I did gxd command and it seen that the procedure
was completed 100% with out error for both XSC and GPU.
Many thanks,
,
Miguel A. Lemus
BIOMEL, S.A. de C.V.
25 calle pte #1254
Col. Layco, San Salvador
El Salvador.
Tel: +503 2226 5599
Fax: +503 2211 5380
Cell phone:+503 7982 6431
Email : biomel@navegante.com.sv
biomedicalemus@gmail.com
to rate and post a comment