I have a problem with Optimus 65 Philips, when power up on unit all leds on control panel are glow up, not flashing, (generator side, all boards),power supply are OK, battery on board 139 and 119 are OK (3V). display on tube side is OK.(power up OK, only system led is out)
Can any one help to solve the problema?. thanks.
When the problem is present no, in few occasion the power up is ok, but in one or two minutes the display the KV, MAS and Ms, is off only lit the leds, no errors
You might have a problem with the console, check Power Supplies on the console. The console boots up and then it communicates with the CPU, so if the console is not booting there are no errors.The normal boot is led's on , led's off(power on self test)and then it display kv mas and ms when it communicates
Hello
Kindly send us email with details your x-ray control panel led is off.no any display any error.when you power up control panel is booting or not also send us photo.
Thanks
Hi, Haroon, I have service manual and terminal with parallel port and Xscope software, and backup disk, but not the hardware key, can I make restore??...thanks
We supply high-quality refurbished and used imaging equipment and parts to hospitals, imaging centers, and brokers worldwide. We pay top dollar and offer installation, deinstallation, service, and transport. Se habla español info@medilabglobal.com
Raul Cervantes
problem Optimus 65 Philips
October 31, 2014 08:57
I have a problem with Optimus 65 Philips, when power up on unit all leds on control panel are glow up, not flashing, (generator side, all boards),power supply are OK, battery on board 139 and 119 are OK (3V). display on tube side is OK.(power up OK, only system led is out)
Can any one help to solve the problema?. thanks.
to rate and post a comment
Juan de la Cruz Martinez
re: problem Optimus 65 Philips
November 01, 2014 02:07
What do you mean system led? Does the Control desk shows the KV mas and MS?
to rate and post a comment
Raul Cervantes
re: re: problem Optimus 65 Philips
November 03, 2014 08:24
Hi, Juan, the control desk, not show KV, mas and ms, only in the cabinet show the 4 leds are lit,(CU, MA, KV and interfase board) not flashing.
to rate and post a comment
Juan de la Cruz Martinez
re: re: re: problem Optimus 65 Philips
November 03, 2014 03:40
Are all the bottoms in the control desk on? do they come on and then they go back off?
to rate and post a comment
Raul Cervantes
re: re: re: re: problem Optimus 65 Philips
November 03, 2014 06:47
When the problem is present no, in few occasion the power up is ok, but in one or two minutes the display the KV, MAS and Ms, is off only lit the leds, no errors
to rate and post a comment
Juan de la Cruz Martinez
re: re: re: re: re: problem Optimus 65 Philips
November 04, 2014 09:01
You might have a problem with the console, check Power Supplies on the console. The console boots up and then it communicates with the CPU, so if the console is not booting there are no errors.The normal boot is led's on , led's off(power on self test)and then it display kv mas and ms when it communicates
to rate and post a comment
Muhammad Muhammad
re: problem Optimus 65 Philips
November 01, 2014 02:08
Hello
Kindly send us email with details your x-ray control panel led is off.no any display any error.when you power up control panel is booting or not also send us photo.
Thanks
to rate and post a comment
Adnan
re: problem Optimus 65 Philips
November 01, 2014 02:10
You need a terminal to retrieve a error log by that log you will find your exact problem. If you have terminal than restore generator backup file.
to rate and post a comment
Haroon Rashid
re: problem Optimus 65 Philips
November 01, 2014 02:11
You need a terminal to retrieve a error log by that log you will find your exact problem. If you have terminal than restore generator backup file.
to rate and post a comment
Raul Cervantes
re: re: problem Optimus 65 Philips
November 03, 2014 08:25
Hi, Haroon, I have service manual and terminal with parallel port and Xscope software, and backup disk, but not the hardware key, can I make restore??...thanks
to rate and post a comment
Haroon Rashid
re: re: re: problem Optimus 65 Philips
November 04, 2014 09:01
No you cannot restore generator without key.for further detail contact me at gems.haroon@hotmail.com
to rate and post a comment