Over 300 Virginia Auctions End Today - Bid Now Over 300 Total Lots Up For Auction at Three Locations - Over 100 California Auctions End Tomorrow 07/22 - Bid Now, KS 07/24, CA 07/31
dear all of you,
my system dit not boot and post this messege:
PXE-E61:Media test failure,check cable
PXE-MOF:Existing Intel Boot Agent
Disk Boot Failue,Insert the System Disk and press Enter
i insert System SW BEP4 and rich to installation menu when choosing A(to reinstall all) or B(repair)i have this message box:
File Name (546)
output error file to the following location
A:\GHOSTERR;TXT
OK Cancel
is any body can tell me what wrong with my sytem
best regars
Appolin
Hopefully you wrote down you s/w keys and or have a backup. The first key is more or less the windows product key, you will find the windows sticker on the BEP. Once you enter that you will then be able to install you backup and that will have all your option keys on it. Note: You are only getting this because you replaced the hdd, if you are re-installing on a drive that had s/w on it in the past you will not see this msg.
Appolin,
I have seen the GE FE's print a hard copy of the configuration and leave it on-site somewhere in the system, If you can not find a copy I think you will have to call GE. Your local engineer should have a copy of all the keys. I do not know of any other way to get the keys for you.
HIGH QUALITY fully tested & refurbished systems to manufacturer specifications like new. Installation & service support worldwide. Parts & tubes in stock with warranty. Sales@Elsmed.com
PIEBENG APPOLIN
problem when loading software in vivid7
November 16, 2009 05:27
dear all of you,
my system dit not boot and post this messege:
PXE-E61:Media test failure,check cable
PXE-MOF:Existing Intel Boot Agent
Disk Boot Failue,Insert the System Disk and press Enter
i insert System SW BEP4 and rich to installation menu when choosing A(to reinstall all) or B(repair)i have this message box:
File Name (546)
output error file to the following location
A:\GHOSTERR;TXT
OK Cancel
is any body can tell me what wrong with my sytem
best regars
Appolin
to rate and post a comment
PIEBENG APPOLIN
Re: problem when loading software in vivid7
November 17, 2009 01:04
hi,
was the bad SATA Driver Disk
but now after reload in new media,
asking LICENCE KEYS.
any adear?
Best Regard
Appolin
to rate and post a comment
Brian Carver
Re: problem when loading software in vivid7
November 18, 2009 10:07
Hopefully you wrote down you s/w keys and or have a backup. The first key is more or less the windows product key, you will find the windows sticker on the BEP. Once you enter that you will then be able to install you backup and that will have all your option keys on it. Note: You are only getting this because you replaced the hdd, if you are re-installing on a drive that had s/w on it in the past you will not see this msg.
Good luck
to rate and post a comment
PIEBENG APPOLIN
Re: problem when loading software in vivid7
November 18, 2009 04:01
hi,
i found licence keys,
install it
and then i can scan now
but there is no backup MO,
what can i do to restore all the option keys in it
Best Regards
Appolin
to rate and post a comment
Brian Carver
Re: problem when loading software in vivid7
November 19, 2009 02:14
Appolin,
I have seen the GE FE's print a hard copy of the configuration and leave it on-site somewhere in the system, If you can not find a copy I think you will have to call GE. Your local engineer should have a copy of all the keys. I do not know of any other way to get the keys for you.
Take care,
Brian
to rate and post a comment
Jim Shami
re: Re: problem when loading software in vivid7
January 13, 2013 09:58
hello
how did you obtain a licence key please infor me i am looking for one let me know please
thanks
jim
to rate and post a comment
fat_sheep
re: Re: problem when loading software in vivid7
May 29, 2016 03:04
Good Day:
Vivid 7, Win XP
System SW BEP4 ver. 2.0.6
Application SW ver. 6.1.1
I have a question concerning my Vivid 7 Win XP machine. Excuse my newbie questioning.
1. Does any of the Vivid 7 comes with embedded Win XP installation and thus would have HDD ? And, based on my info. would it come with it.
2. What exactly is the installation procedure for this machine using my System SW BEP4?
3. Why & When would you use the license key or when is it requested ?
p.s.
*** my email: nshepherd123@gmail.com
to rate and post a comment
Fabio Barcherini
Re: problem when loading software in vivid7
February 04, 2012 12:23
Hello guys
I need sw Sys 1.5.2 and application 2.6.4 for Vivid 7 Bep 2 .
Have you ?
to rate and post a comment