Hello team OEC
can you help me, i have some problems for start OEC9400, this machine no wokk since long time, C-arm no start, just this chronologie
MST
PLEASE WAIT 04
PLEASE WAIT B04
DRIVE NOT READY
RETRYING DISK
ALSO THE BAR GRAF BATTERY IS 200
DIGIT BOARD PROCESSOR IS 2
DIGITS REAR BLOC MONITOR IS FF
THE BATTERY MOTHER BOARD IS LOW ? VERY LOW 0V
THE BATTERYS c6ARM? LOW? VERY LOW.
ANY SCRIPTS LOADING SYSTEM IN MONITOR? ANY IMAGES
DO YOU HAVE SOMES IDEES TO HELP ME? TOMORROW I CHANGE BATTERY MOTHER BOARD
CHEK POWERS SUPPLY .
THANKS IN ADVANCE
ROGER
email rdus0001@yahoo.fr
Hello Roger.
you have to check the floppy driver or the floppy disk maybe it not work properly. remember the floppy disk driver is SONY 720kb not 1.44mb
change the battery backup in motherboard and clean the dirver floppy or try with anoter floppy disk.
try to format a new floppy disk (1.44mb IBM fotmat) to FAT at 720kb, how? cover the hole with a black tape and copy your original floppy disk. remember put the original disk in read only (tab)
good luck.
Julio C. Gomez
pruebadecampo@yahoo.es
Veracruz, Mexico.
THANKS JULIO. today i was remove the packs battery, all packs is bad, tension 0volts. i can change with battery buy in local market . 30pieces of 6 volts.IT IS NECESSERY TO BUY ITS IF IS IT POSSIBLE TO TCHEK LOADIND CORRECT OEC SYSTEM
Lightly used system available direct from the end user customer. MONARCH QUEST
Featuring our most advanced, data-driven navigation software with AI-Powered algorithms & advanced imaging integration with the GE HealthCare OEC 3D C-arm.
roger dussart
probleme start OEC9400
May 10, 2012 03:06
Hello team OEC
can you help me, i have some problems for start OEC9400, this machine no wokk since long time, C-arm no start, just this chronologie
MST
PLEASE WAIT 04
PLEASE WAIT B04
DRIVE NOT READY
RETRYING DISK
ALSO THE BAR GRAF BATTERY IS 200
DIGIT BOARD PROCESSOR IS 2
DIGITS REAR BLOC MONITOR IS FF
THE BATTERY MOTHER BOARD IS LOW ? VERY LOW 0V
THE BATTERYS c6ARM? LOW? VERY LOW.
ANY SCRIPTS LOADING SYSTEM IN MONITOR? ANY IMAGES
DO YOU HAVE SOMES IDEES TO HELP ME? TOMORROW I CHANGE BATTERY MOTHER BOARD
CHEK POWERS SUPPLY .
THANKS IN ADVANCE
ROGER
email rdus0001@yahoo.fr
to rate and post a comment
Wayne Horsman
re: probleme start OEC9400
May 10, 2012 11:50
B4 = Bad Workstation floppy, or Tech. Processor PCB
Try using the backup copy of the floppy disk.
to rate and post a comment
Julio c. Gomez
re: probleme start OEC9400
May 11, 2012 09:55
Hello Roger.
you have to check the floppy driver or the floppy disk maybe it not work properly. remember the floppy disk driver is SONY 720kb not 1.44mb
change the battery backup in motherboard and clean the dirver floppy or try with anoter floppy disk.
try to format a new floppy disk (1.44mb IBM fotmat) to FAT at 720kb, how? cover the hole with a black tape and copy your original floppy disk. remember put the original disk in read only (tab)
good luck.
Julio C. Gomez
pruebadecampo@yahoo.es
Veracruz, Mexico.
to rate and post a comment
roger dussart
re: re: probleme start OEC9400
May 11, 2012 11:11
THANKS JULIO. today i was remove the packs battery, all packs is bad, tension 0volts. i can change with battery buy in local market . 30pieces of 6 volts.IT IS NECESSERY TO BUY ITS IF IS IT POSSIBLE TO TCHEK LOADIND CORRECT OEC SYSTEM
to rate and post a comment