This can be a few things. Check voltages going to your hard drive. Should be 12 and 5v present at the hard drive. If voltage present it could be an issue with the #12 CPU board which has two components, the lower board and upper board. The larger lower board commonly has the scsi error as well. That should give you somewhere to start.
Hi everyone,
I have the same problem on my Logiq 400, someone told me that it also could be the ram battery on the CPU board the thing is that once this battery dies you have to reconfigure the CPU board, is this true??? does someone know how to do this????
Any help will be appreciate it,
Tomas, The timekeeper RAM you refer to above will give a different error. When the system references the SCSI it is a drive/interface problem. Since the system normally boots from the HDD this is the most likely drive referenced by the error. All the best, Ron.
Thanks Ron,
I changed the battery and system is booting up, the only problem I have right now is a bat date and time, system will not let me change it.
Amoako Eric
scsi error logiq 400MD
January 13, 2014 10:12
Hi all, My logiq 400md problem, start of diagnostic is not run. it show SCSI ERROR CODE 20166. can same one help me.aketech4@gmail.com TANK U.
to rate and post a comment
Ricardo Armenta
re: scsi error logiq 400MD
January 13, 2014 08:27
check the Hard Drive
to rate and post a comment
SUNGHYUN HAN
re: scsi error logiq 400MD
January 14, 2014 10:26
This is HDD drive problem.
to rate and post a comment
moito
re: scsi error logiq 400MD
January 14, 2014 10:26
replace HD
It's below keyboard
view software version
to rate and post a comment
Zach Ruder
re: scsi error logiq 400MD
January 14, 2014 10:27
This can be a few things. Check voltages going to your hard drive. Should be 12 and 5v present at the hard drive. If voltage present it could be an issue with the #12 CPU board which has two components, the lower board and upper board. The larger lower board commonly has the scsi error as well. That should give you somewhere to start.
to rate and post a comment
Tomas Camargo
re: re: scsi error logiq 400MD
January 14, 2014 01:45
Hi everyone,
I have the same problem on my Logiq 400, someone told me that it also could be the ram battery on the CPU board the thing is that once this battery dies you have to reconfigure the CPU board, is this true??? does someone know how to do this????
Any help will be appreciate it,
thanks in advance
Tomas Camargo
tcamargo3@gmail.com
619-730-1020
to rate and post a comment
Ron Morey
re: re: re: scsi error logiq 400MD
January 20, 2014 01:07
Tomas, The timekeeper RAM you refer to above will give a different error. When the system references the SCSI it is a drive/interface problem. Since the system normally boots from the HDD this is the most likely drive referenced by the error. All the best, Ron.
to rate and post a comment
Tomas Camargo
re: re: re: re: scsi error logiq 400MD
January 20, 2014 05:00
Thanks Ron,
I changed the battery and system is booting up, the only problem I have right now is a bat date and time, system will not let me change it.
to rate and post a comment
Ron Morey
re: re: re: re: re: scsi error logiq 400MD
January 20, 2014 06:17
Tomas, send me your email address and I will send you the instructions regarding changing the date/time and system ID.
All the best, Ron.
to rate and post a comment
Tomas Camargo
re: re: re: re: re: re: scsi error logiq 400MD
January 21, 2014 12:05
Thanks Ron,
Here it's tcamargo3@gmail.com
Thanks again and have a great day.
to rate and post a comment
Tomas Camargo
re: re: re: re: re: re: scsi error logiq 400MD
January 21, 2014 12:06
Ron, can you please send me a # so I can call you, send to tcamargo3@gmail.com
to rate and post a comment
Manjul Kumar
re: scsi error logiq 400MD
January 16, 2014 04:16
This is a c p U board error. Change it & check. Ur pblm will b solved...
to rate and post a comment