Siemens Poly Mobile 3 we are using developed a fault and the transformer was changed.
After that we noticed an error 03 on the machine.
What can be the problem?
Thank you.
Error 3 - Oil pressure rise or overheating of the tube
Error 3 Oil pressure rise or overheating of the tube
System status:
Standby
Explanation:
Action:
• Check the oil switch.
(Normal tube condition = switch closed)
Warning: let the tube cool off before testing!
• Check the connections and the cable between the switch
and the D916 X8-9 and X8-8.
good luck
also i have all manuals for this system if you need them contact me
Thank you Mohammed,I will send you a mail.
Meanwhile i got a tip from the guy using the machine that the Poly-mobile 3 is showing both error "03 & 06"
What could be the problem?
error 6 Explanation:
Action:
• Compare IH and IHS in D916 to make sure they are not the
same.
• Check the frequency of the heating inverter in the D916
TP - FC1.
• Check the form of the resonance current at the TP-I D916
(use Service Program 9).
Possible causes are a bad cable connection from
D916 to D1(X8) (high resistance) to the single tank, a
defective heating inverter on board D922, a defective
heating transformer (single tank), the filament in the
single tank is defective, the D916 and/or the D922 are
defective, or the tube is defective.
Hi Ernest, is so important to have which polimobil 3 model do you have, because there are two version, one serial 3000 and up and another serial 3000 down and new models serial 2000 or higher, what is you model?....
Specializing in GE, we keep your ICU monitors calibrated and patient-ready—fast, reliable service from expert biomed techs. Southeastern Biomedical: 888-310-7322.
Ernest ONUIGBO
Siemens Polymobile 3
February 24, 2014 08:35
Dear All,
Siemens Poly Mobile 3 we are using developed a fault and the transformer was changed.
After that we noticed an error 03 on the machine.
What can be the problem?
Thank you.
nestob2002@yahoo.com
+4368110738485
Best regards
Ernest Onuigbo
to rate and post a comment
Mohammed Abdullah
re: Siemens Polymobile 3
February 24, 2014 02:42
Dear Ernest,
Error 3 - Oil pressure rise or overheating of the tube
Error 3 Oil pressure rise or overheating of the tube
System status:
Standby
Explanation:
Action:
• Check the oil switch.
(Normal tube condition = switch closed)
Warning: let the tube cool off before testing!
• Check the connections and the cable between the switch
and the D916 X8-9 and X8-8.
good luck
also i have all manuals for this system if you need them contact me
magmesme@gmail.com
regards
to rate and post a comment
Ernest ONUIGBO
re: re: Siemens Polymobile 3
February 25, 2014 08:51
Thank you Mohammed,I will send you a mail.
Meanwhile i got a tip from the guy using the machine that the Poly-mobile 3 is showing both error "03 & 06"
What could be the problem?
to rate and post a comment
Mohammed Abdullah
re: re: re: Siemens Polymobile 3
February 25, 2014 12:15
Dear Ernesr,
Error 06 mean:
Error 6 - IH heating measured
to rate and post a comment
Mohammed Abdullah
re: re: re: Siemens Polymobile 3
February 25, 2014 06:29
error 6 Explanation:
Action:
• Compare IH and IHS in D916 to make sure they are not the
same.
• Check the frequency of the heating inverter in the D916
TP - FC1.
• Check the form of the resonance current at the TP-I D916
(use Service Program 9).
Possible causes are a bad cable connection from
D916 to D1(X8) (high resistance) to the single tank, a
defective heating inverter on board D922, a defective
heating transformer (single tank), the filament in the
single tank is defective, the D916 and/or the D922 are
defective, or the tube is defective.
to rate and post a comment
jorge mazariegos
re: re: Siemens Polymobile 3
February 26, 2016 08:45
good afternoon sorry I look for the service manual siemens polymobile 3 could help thanks
to rate and post a comment
DMEDS
re: re: re: Siemens Polymobile 3
February 28, 2016 04:16
Dear Sir,
I have the manuals you need,
if you need it contact me,
magmesme@gmail.com
Regards
to rate and post a comment
hemrajsinh chauhan
re: re: re: re: Siemens Polymobile 3
March 20, 2019 09:56
I need manual and schematics pleas send me on raj_meditech@hotmail.com
to rate and post a comment
hemrajsinh chauhan
re: re: Siemens Polymobile 3
March 20, 2019 09:56
I need it sir please send me on raj_meditech@hotmail.com
to rate and post a comment
Jairo Manzaneda
re: Siemens Polymobile 3
February 25, 2014 08:43
Hi Ernest, is so important to have which polimobil 3 model do you have, because there are two version, one serial 3000 and up and another serial 3000 down and new models serial 2000 or higher, what is you model?....
to rate and post a comment