We´re having a little trouble in here.
We tried to install the SW into a Voluson 730 PRO with BT05 (5.0.2) but everytime we do that the system is unable to continue the boot from the DVD disk.
I managed to open the DVD menu for reloading the software, I turned off the machine to make a HDD image, the I restarted the machine and I was never able again to continue with the reload because the DVD fails to continue the process.
I thought the DVD disc was badly so I burned again the image and the result was always the same.
I tried to boot with the discs in other platforms and the discs always shows the same message.
Any ideas about why the DVD disc is unable to continue its process?
The boot order is OK with USB-CD room as first priority, the HDD is set as master.
By the way, I´m trying to replace the BT05 5.0.2 with the 5.0.5 (are there any major differences between both versions?)
Hope anybody can lend me a hand with this
The system should load 5.0.5 without a problem. I wonder if someone put a different DVD drive in it, one not supported by GE's software? It should be a Yamaha DVD+(R)W with an IDE interface. There is a USB to IDE converter inside the GEM box that houses the drives.
Do you know if there is a Full System Backup saved to the hard drive? The R partition should contain all the software, Window, Applications and the Option key(s) that are needed to get your system running.
Also, have you tested the hard drive to see if it is OK. The software load may be failing because of bad sectors on the disk.
Looking for the leader in urology? BK Medical is and we are the 3rd party experts. We sell BK and many other brands. Call today to discuss your urology equipment needs and save $1,000’s! Call Today: 1-888-838-7488 Email: sales@sentinelimaging.net
Billy Sanchez Olivares
Voluson 730PRO
September 30, 2017 04:42
We´re having a little trouble in here.
We tried to install the SW into a Voluson 730 PRO with BT05 (5.0.2) but everytime we do that the system is unable to continue the boot from the DVD disk.
I managed to open the DVD menu for reloading the software, I turned off the machine to make a HDD image, the I restarted the machine and I was never able again to continue with the reload because the DVD fails to continue the process.
I thought the DVD disc was badly so I burned again the image and the result was always the same.
I tried to boot with the discs in other platforms and the discs always shows the same message.
Any ideas about why the DVD disc is unable to continue its process?
The boot order is OK with USB-CD room as first priority, the HDD is set as master.
By the way, I´m trying to replace the BT05 5.0.2 with the 5.0.5 (are there any major differences between both versions?)
Hope anybody can lend me a hand with this
to rate and post a comment
Murat Canpolat
re: Voluson 730PRO
October 02, 2017 09:33
Hello Billy
try to ide dvd room with ide cable or sata dvd room with sata cable direct connect to mainboard or sbc.
muratcanpolat@hotmail.com.tr
to rate and post a comment
Ricardo A. Sanchez
re: Voluson 730PRO
October 03, 2017 09:13
sen me an email ricardo@ultrasolutions.com
to rate and post a comment
Jim Carr
re: Voluson 730PRO
October 04, 2017 09:18
Howdy Billy,
The system should load 5.0.5 without a problem. I wonder if someone put a different DVD drive in it, one not supported by GE's software? It should be a Yamaha DVD+(R)W with an IDE interface. There is a USB to IDE converter inside the GEM box that houses the drives.
Do you know if there is a Full System Backup saved to the hard drive? The R partition should contain all the software, Window, Applications and the Option key(s) that are needed to get your system running.
Also, have you tested the hard drive to see if it is OK. The software load may be failing because of bad sectors on the disk.
Best regards,
Jim Carr
to rate and post a comment